夹具订制
AGG可在机械手和模具间提供精i准的中心。
注塑模具内金属嵌件安放时尤其要注意这一点。
夹具AGG...B 安装在EOAT上，钢管 AGG...C 安装在模具上。
一旦机械手向模具靠近，夹具在压力的作用下逐步向钢管靠近，
并与之接触。
AGG21-B 和 AGG30-B 采用的是双动作安全弹簧，机械手气动夹爪，确保在压缩空
气 (NC)缺失时设备的正常运行。
AGG19-B 采用的是单动作复位弹簧(NO)。
Gripper for engagement
The AGG is used to provide a precise centering between the robot
and the mould.
This necessary when metal inserts must be p1aced in the
mould， before the p1astic injection.
The gripper AGG…-B is fitted on the EOAT， while the steel bushing
AGG…-C is fitted on the mould.
Once the robot has approached the mould， the gripper is
pressurized， thus it closes and engages the bushing.
AGG21-B and AGG30-B are double-acting with a safety spring to
keep the gripper engaged even without compressed air (NC).
AGG19-B is single-acting with reset spring (NO).
吸盘/硅氧烷
VG.BC40S 硅氧烷多波纹管吸盘
? 适用于处理装有易碎品的袋子和装有液体和冷冻食品的袋子
? 坚固的波纹管，柔软灵活的唇口和特殊的高流量配件
? 带 4.5 波纹管的版本
? 它们能补偿真空度差异
技术数据
材料 SIL 40
体积 14cm3
zui小曲线半径22mm
zui大垂直移动距离20mm
吸盘质量10g
编程单个SB8F
在对传感器盒进行编程之前，请确保有线输入处于所需配置（开/关）以启用输出。按下AUTOSET按钮并按住3秒钟，电动夹爪，直到READING红灯开始闪烁，锦州夹爪，然后松开。红灯（READING）闪烁表示微处理器正在读取和存储全部输入的状态。然后红灯熄灭，启用了输出。黄灯（STORED）指示启用输出。
Before programming the sensor box， make sure that the wired inputs are in the confguration (ON/OFF) desired to enable the output. Press the AUTOSET button and hold it down for 3 seconds until the READING red light starts fashing， then release it.The red light (READING) fashing indicates that the microprocessor is reading and storing the state of all the inputs. Then the red light goes off and the output is enabled. Output enabling is indicated by the yellow light (STORED).
锦州夹爪-电动夹爪-吉玛泰克(推荐商家)由吉玛泰克自动化工程（常熟）有限公司提供。吉玛泰克自动化工程（常熟）有限公司坚持“以人为本”的企业理念，拥有一支高素质的员工队伍，力求提供更好的产品和服务回馈社会，并欢迎广大新老客户光临惠顾，真诚合作、共创美好未来。吉玛泰克——您可信赖的朋友，公司地址：江苏省常熟市古里镇通华路1号2幢，联系人：吴琦。